 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Agilent E5071C ENA Network Analyzer * 9 kHz to 4.5/6.5/8.5 GHz * 100 kHz to 4.5/6.5/8.5 GHz (with bias tees) * 300 kHz to 14/20 GHz (with bias tees) E5091A Multiport Test Set E5092A Configurable Multiport Test Set Data Sheet www..com Table of Contents Options ........................................................................................................................ 3 Definitions ................................................................................................................. 4 Boundary Conditions ............................................................................................. 4 Corrected System Performance........................................................................ 5 System dynamic range ..................................................................................................... 5 Corrected system performance with calibration kit.................................................... 7 Uncorrected System Performance ................................................................13 Test Port Output (Source) .................................................................................14 Test port output frequency ............................................................................................14 Test port output power ..................................................................................................15 Test port output signal purity ........................................................................................17 Test Port Input ........................................................................................................18 Test port input levels ......................................................................................................18 Test port input (trace noise) ..........................................................................................20 Test port input (stability) ...............................................................................................22 Test port input (dynamic accuracy) ..............................................................................23 Test port input (group delay) .........................................................................................25 General Information.............................................................................................27 System bandwidths .........................................................................................................27 Front panel information ..................................................................................................27 Rear panel information ...................................................................................................28 LXI compliance.................................................................................................................30 EMC, safety and environment .......................................................................................31 Analyzer environmental specifications and dimensions ..........................................32 Measurement Throughput Summary ............................................................36 Typical cycle time for measurement completion (ms)..............................................36 Cycle time (ms) vs. number of points..........................................................................48 Cycle time (ms) vs. IF bandwidth .................................................................................49 Data transfer time (ms) ..................................................................................................50 E5091A Multiport Test Set.................................................................................51 Test set input/output performance ..............................................................................51 Option E5091A-009 port performance .........................................................................51 Option E5091A-016 port performance .........................................................................52 Front panel information ..................................................................................................52 Rear panel information ...................................................................................................52 Test set dimensions and block diagram ......................................................................53 E5092A Configurable Multiport Test Set .....................................................56 Test set input/output performance ..............................................................................56 Option E5092A-020 port performance .........................................................................56 Control line .......................................................................................................................58 www..com DC source..........................................................................................................................58 Operating storage environment ....................................................................................58 Non-operating storage environment ............................................................................58 Front panel information ..................................................................................................59 Rear panel information ...................................................................................................59 Test set dimensions and block diagram ......................................................................59 Corrected System Performance for 75 Measurements with 11852B 50 to 75 Minimum-Loss Pads ................................................63 2 Options This document provides technical specifications for the E5071C ENA network analyzer and the E5091A multiport test set. E5071C-230 E5071C-235 E5071C-240 E5071C-245 E5071C-260 E5071C-265 E5071C-280 E5071C-285 E5071C-430 E5071C-435 E5071C-440 E5071C-445 E5071C-460 E5071C-465 E5071C-480 E5071C-485 E5071C-2D5 E5071C-4D5 E5071C-2K5 E5071C-4K5 E5091A E5092A 2-port test set, 9 kHz to 3 GHz without bias tees (Discontinued) 2-port test set, 100 kHz to 3 GHz with bias tees (Discontinued) 2-port test set, 9 kHz to 4.5 GHz without bias tees 2-port test set, 100 kHz to 4.5 GHz with bias tees 2-port test set, 9 kHz to 6.5 GHz without bias tees 2-port test set, 100 kHz to 6.5 GHz with bias tees 2-port test set, 9 kHz to 8.5 GHz without bias tees 2-port test set, 100 kHz to 8.5 GHz with bias tees 4-port test set, 9 kHz to 3 GHz without bias tees (Discontinued) 4-port test set, 100 kHz to 3 GHz with bias tees (Discontinued) 4-port test set, 9 kHz to 4.5 GHz without bias tees 4-port test set, 100 kHz to 4.5 GHz with bias tees 4-port test set, 9 kHz to 6.5 GHz without bias tees 4-port test set, 100 kHz to 6.5 GHz with bias tees 4-port test set, 9 kHz to 8.5 GHz without bias tees 4-port test set, 100 kHz to 8.5 GHz with bias tees 2-port test set, 300 kHz to 14 GHz with bias tees 4-port test set, 300 kHz to 14 GHz with bias tees 2-port test set, 300 kHz to 20 GHz with bias tees 4-port test set, 300 kHz to 20 GHz with bias tees Multiport test set Configurable multiport test set Calibration kits and ECal modules This E5071C data sheet also provides technical specifications for the following calibration kits and ECal modules. For models not listed in this data sheet, please download the free Uncertainty Calculator from www.agilent.com/find/na_calculator to generate the curves for your calibration kit and enable ENA setup. 85032F 85033E 85052D 85092C 85093C N4691B Calibration kit Calibration kit Calibration kit Electronic calibration (ECal) module Electronic calibration (ECal) module Electronic calibration (ECal) module www..com 3 Definitions Specification (spec.): Warranted performance. All specifications apply at 23 C ( 5 C), unless otherwise stated, and 90 minutes after the instrument has been turned on. Specifications include guard bands to account for the expected statistical performance distribution, measurement uncertainties, and changes in performance due to environmental conditions. Supplemental information is intended to provide information that is helpful for using the instrument but that is not guaranteed by the product warranty. Typical (typ.): Describes performance that will be met by a minimum of 80% of all products. It is not guaranteed by the product warranty. Supplemental performance data (SPD): Supplemental performance data represents the value of a parameter that is most likely to occur; the expected mean or average. It is not guaranteed by the product warranty. General characteristics: A general, descriptive term that does not imply a level of performance. Boundary Conditions In this data sheet, boundary conditions are given for the specifications. For example, system dynamic range is 98 dB with the following boundary conditions. Option: 485 Frequency: 10 MHz IF bandwidth: 3 kHz If the same boundary conditions fall under more than one category in a table, apply the best value. www..com 4 Corrected System Performance The specifications in this section apply to measurements made with the Agilent E5071C network analyzer under the following conditions: * No averaging applied to data * Environmental temperature of 23 C (5 C) with less than 1 C deviation from the calibration temperature * Response and isolation calibration performed System dynamic range Table 1. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Description System dynamic range1, 2 9 kHz to 300 kHz 300 kHz to 10 MHz 10 MHz to 6 GHz 6 GHz to 8.5 GHz 9 kHz to 300 kHz 300 kHz to 10 MHz 10 MHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8 GHz 8 GHz to 8.5 GHz IF bandwidth = 10 Hz IF bandwidth = 3 kHz 72 dB 82 dB 98 dB 92 dB 97 dB 107 dB 123 dB 117 dB 117 dB 117 dB 115 dB 115 dB 130 dB 128 dB 126 dB 124 dB Specification SPD 160 System dynamic range [dB] 150 140 130 120 110 100 90 80 1.E+05 1.E+09 2.E+09 3.E+09 4.E+09 5.E+09 6.E+09 7.E+09 8.E+09 E5071C specification Test frequency [Hz] www..com Figure 1. System dynamic range (specification and actual measurement data example, IF bandwidth 10 Hz) 1. The test port dynamic range is calculated as the difference between the test port rms noise floor and the source maximum output power. The effective dynamic range must take measurement uncertainty and interfering signals into account. 2. The specification might not be met at 5 MHz or 50 MHz. 5 System dynamic range (continued) Table 2. Option 2D5/2K5/4D5/4K5 Description System dynamic range1, 2 300 kHz to 1 MHz 1 MHz to 10 MHz 10 MHz to 100 MHz 100 MHz to 6 GHz 6 GHz to 8.5 GHz 8.5 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz 300 kHz to 1 MHz 1 MHz to 10 MHz 10 MHz to 100 MHz 100 MHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 8.5 GHz 8.5 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz IF bandwidth = 10 Hz IF bandwidth = 3 kHz 70 dB 82 dB 95 dB 98 dB 92 dB 80 dB 75 dB 71 dB 95 dB 107 dB 120 dB 123 dB 117 dB 117 dB 105 dB 100 dB 96 dB 105 dB 115 dB 129 dB 130 dB 129 dB 127 dB 115 dB 111 dB 105 dB Specification SPD 160 150 System dynamic range[dB] 140 130 120 110 100 90 80 0.0E+00 5.0E+09 E5071C-2D5/2K5/4D5/4K5 specification 1.0E+10 1.5E+10 2.0E+10 Frequency [Hz] Figure 2. System dynamic range (specification and actual measurement data example, IF bandwidth 10 Hz) www..com 1. The test port dynamic range is calculated as the difference between the test port's rms noise floor and the source's maximum output power. Effective dynamic range must take measurement uncertainty and interfering signals into account. 2. The specification might not be met at 5 MHz or 50 MHz. 6 Corrected system performance with calibration kit Option 230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485 Table 3. Corrected system performance with type-N device connectors, 85032F calibration kit Network analyzer: Calibration kit: Calibration: E5071C 85032F (Type-N, 50 ) full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 9 kHz to 300 kHz 49 41 49 0.011 0.027 300 kHz to 10 MHz 49 41 49 0.011 0.015 10 MHz to 3 GHz 46 40 46 0.021 0.018 3 GHz to 6 GHz 40 36 40 0.032 0.056 6 GHz to 8.5 GHz 38 35 37 0.054 0.088 Transmission uncertainty (specification) 10 Magnitude 100 9 KHz to 300 KHz 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Phase 9 KHz to 300 KHz 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Uncertainty (degrees) Uncertainty (dB) 1 10 0.1 1 0.01 10 S 1 1 = S 2 2 = 0 ; C a l p o w e r = -1 0 d B m ; M e a s p o w e r = -1 0 d B m 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 0.1 10 0 -10 S 1 1 = S 2 2 = 0 ; C a l p o w e r = -1 0 d B m ; M e a s p o w e r = -1 0 d B m -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Transmission coefficient (dB) Reflection uncertainty (specification) Magnitude 0.05 9 KHz to 300 KHz, 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz 10 8 6 4 2 Phase 9 KHz to 300 KHz, 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz 0.03 www..com 0.02 0.01 S21 = S12 = 0; Cal power = -10 dBm; Meas power = -10 dBm Uncertainty (degrees) Uncertainty (linear) 0.04 S21 = S12 = 0; Cal power = -10 dBm; Meas power = -10 dBm 0 0 0.2 0.4 0.6 0.8 1 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) Reflection coefficient (linear) 7 Table 4. Corrected system performance with type-N device connectors, 85092C electronic calibration (ECal) module Network analyzer: Calibration module: Calibration: E5071C 85092C (Type-N, 50 ) Electronic calibration (ECal) module full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 300 kHz to 10 MHz 45 36 41 0.100 0.055 10 MHz to 3 GHz 52 44 47 0.040 0.039 3 GHz to 6 GHz 52 41 44 0.060 0.068 6 GHz to 8.5 GHz 47 36 39 0.070 0.136 Transmission uncertainty (specification) Magnitude 10 3 0 0 K H z to 1 0 M H z 1 0 M H z to 3 G H z 6 G H z to 8 .5 G H z 3 G H z to 6 G H z Phase 100 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z Uncertainty (degrees) 3 G H z to 6 G H z 6 G H z to 8 .5 G H z Uncertainty (dB) 1 10 0 .1 1 S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 0 .1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 Transmission coefficient (dB) Transmission coefficient (dB) Reflection uncertainty (specification) Magnitude 0 .0 5 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z Phase 10 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z 3 G H z to 6 G H z 6 G H z to 8 .5 G H z S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 4 3 G H z to 6 G H z 8 Uncertainty (linear) www..com 0 .0 2 0 .0 3 S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm Uncertainty (linear) 0 .8 1 6 G H z to 8 .5 G H z 6 4 0 .0 1 2 0 0 0 .2 0 .4 0 .6 0 0 0 .2 0 .4 0 .6 0 .8 1 Reflection coefficient (linear) Reflection coefficient (linear) 8 Table 5. Corrected system performance with 3.5 mm device connector type, 85033E calibration kit Network analyzer: Calibration kit: Calibration: E5071C 85033E (3.5 mm, 50 ) full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 9 kHz to 300 kHz 46 43 46 0.006 0.026 300 kHz to 10 MHz 46 43 46 0.006 0.015 10 MHz to 3 GHz 44 40 44 0.007 0.020 3 GHz to 6 GHz 38 37 38 0.009 0.058 6 GHz to 8.5 GHz 38 36 38 0.010 0.079 Transmission uncertainty (specification) 10 Magnitude 9 KHz to 300 KHz 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz 100 Phase 9 KHz to 300 KHz 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Uncertainty (degrees) Uncertainty (dB) 1 10 0.1 1 S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 0.1 10 0 -10 S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Transmission coefficient (dB) Reflection uncertainty (specification) Magnitude 0.05 9 KHz to 300 KHz, 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz 10 8 6 4 2 Phase 9 KHz to 300 KHz, 300 KHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Uncertainty (linear) 0.04 0.03 0.02 0.01 0 0 www..com Uncertainty (degrees) S21 = S12 = 0; Cal power = -10 dBm; Meas power = -10 dBm S21 = S12 = 0; Cal power = -10 dBm; Meas power = -10 dBm 0 Reflection coefficient (linear) 0.2 0.4 0.6 0.8 1 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 9 Table 6. Corrected system performance with 3.5 mm device connector type, 85093C electronic calibration (ECal) module Network analyzer: Calibration module: Calibration: E5071C 85093C (3.5 mm, 50 ) electronic calibration (ECal) module full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 300 kHz to 10 MHz 45 36 41 0.100 0.055 10 MHz to 3 GHz 52 44 47 0.040 0.049 3 GHz to 6 GHz 51 39 44 0.050 0.068 6 GHz to 8.5 GHz 47 34 40 0.070 0.117 Transmission uncertainty (specification) Magnitude 10 3 0 0 K Hz to 1 0 MHz 1 0 MHz to 3 G Hz 3 G Hz to 6 G Hz 6 G Hz to 8 .5 G Hz Phase 100 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z 3 G H z to 6 G H z 6 G H z to 8 .5 G H z Uncertainty (degrees) Uncertainty (dB) 1 10 0 .1 1 S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 0 .1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 Transmission coefficient (dB) Transmission coefficient (dB) Reflection uncertainty (specification) Magnitude 0 .0 5 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z Phase 10 3 0 0 kH z to 1 0 M H z 1 0 M H z to 3 G H z 3 G H z to 6 G H z 6 G H z to 8 .5 G H z S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 4 3 G H z to 6 G H z 6 G H z to 8 .5 G H z 8 0 .0 3 S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm Uncertainty (degrees) 0 .8 1 Uncertainty (linear) 6 www..com 0 .0 2 0 .0 1 4 2 0 0 0 .2 0 .4 0 .6 0 0 0 .2 0 .4 0 .6 0 .8 1 Reflection coefficient (linear) Reflection coefficient (linear) 10 Option 2D5/2K5/4D5/4K5 Table 7. Corrected system performance with 3.5 mm device connectors, 85052D calibration kit Network analyzer: Calibration kit: Calibration: E5071C 85052D (3.5 mm, 50 ) full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 300 kHz to 500 MHz 42 37 42 0.003 0.068 500 MHz to 2 GHz 42 37 42 0.003 0.034 2 GHz to 6 GHz 38 31 38 0.004 0.100 6 GHz to 20 GHz 36 28 36 0.008 0.208 Transmission uncertainty (specification) Magnitude 10 3 0 0 K H z to 5 0 0 M H z 2 G H z to 6 G H z 6 G H z to 2 0 G H z Phase 100 3 0 0 K H z to 5 0 0 M H z Uncertainty (Degrees) 5 0 0 M H z to 2 G H z 5 0 0 M H z to 2 G H z 2 G H z to 6 G H z Uncertainty (dB) 1 10 6 G H z to 2 0 G H z 0 .1 1 S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 1 10 0 S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm 0 .1 -10 -20 -30 -40 -50 -60 -70 -80 -90 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 Transmission Coefficient (dB) T rans mis s ion C oefficient (dB ) Reflection uncertainty (specification) Magnitude 0 .0 5 3 0 0 K H z to 5 0 0 M H z, 5 0 0 M H z to 2 G H z Phase 10 3 0 0 K H z to 5 0 0 M H z, 5 0 0 M H z to 2 G H z 2 G H z to 6 G H z 6 G H z to 2 0 G H z 0 .0 4 2 G H z to 6 G H z 6 G H z to 2 0 G H z 8 Uncertainty (degrees) Uncertainty (linear) S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 3 www..com 0 .0 2 6 4 0 .0 1 S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 2 0 0 0 .2 0 .4 0 .6 0 .8 1 0 0 0 .2 0 .4 0 .6 0 .8 1 Reflection coefficient (linear) Reflection coefficient (linear) 11 Table 8. Corrected system performance with 3.5 mm device connectors, N4691B electronic calibration (ECal) module Network analyzer: Calibration module: Calibration: E5071C N4691B (3.5 mm, 50 ) electronic calibration (ECal) module full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C (5 C ) with < 1 C deviation from calibration temperature, isolation calibration performed Specification (dB) Description Directivity Source match Load match Reflection tracking Transmission tracking 10 MHz to 500 MHz 46 41 38 0.050 0.087 500 MHz to 2 GHz 56 47 41 0.020 0.086 2 GHz to 6 GHz 54 45 39 0.030 0.097 6 GHz to 20 GHz 48 44 36 0.040 0.130 Transmission uncertainty (specification) Magnitude 10 1 0 M H z to 5 0 0 M H z 5 0 0 M H z to 2 G H z 2 G H z to 6 G H z Phase 100 1 0 M H z to 5 0 0 M H z 5 0 0 M H z to 2 G H z 2 G H z to 6 G H z 6 G H z to 2 0 G H z Uncertainty (dB) 1 6 G H z to 2 0 G H z Uncertainty (Degrees) 10 0 .1 1 S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10dBm S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10dBm 0 .0 1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 0 .1 10 0 -1 0 -2 0 -3 0 -4 0 -5 0 -6 0 -7 0 -8 0 -9 0 Transmission Coefficient (dB) Transmission Coefficient (dB) Reflection uncertainty (specification) Magnitude 0 .0 5 1 0 M H z to 5 0 0 M H z 5 0 0 M H z to 2 G H z Phase 10 1 0 M H z to 5 0 0 M H z 5 0 0 M H z to 2 G H z 2 G H z to 6 G H z 6 G H z to 2 0 G H z 0 .0 4 2 G H z to 6 G H z 8 Uncertainty (degrees) 6 G H z to 2 0 G H z Uncertainty (linear) S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm S 2 1 = S 1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm 0 .0 3 6 www..com 0 .0 2 4 0 .0 1 2 0 0 0 .2 0 .4 0 .6 0 .8 1 0 0 0 .2 0 .4 0 .6 0 .8 1 Reflection coefficient (linear) Reflection coefficient (linear) 12 Uncorrected System Performance Table 9. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 User correction: OFF, system correction: ON Specification (dB) Description Directivity Source match Load match Transmission tracking Reflection tracking 9 kHz to 300 kHz 20 dB 20 dB 12 dB 1.5 dB 1.5 dB 300 kHz to 3 GHz 25 dB 25 dB 17 dB 1.0 dB 1.0 dB 3 GHz to 6 GHz 20 dB 20 dB 12 dB 1.0 dB 1.0 dB 6 GHz to 8.5 GHz 15 dB 15 dB 10 dB 1.0 dB 1.0 dB Table 10. Option 2D5/2K5/4D5/4K5 User correction: OFF, system correction: ON Specification (dB) Description Directivity Load match 300 kHz 1 MHz to 1 GHz to 3 GHz to 6 GHz to to 1 MHz 1 GHz 3 GHz 6 GHz 8.5 GHz 20 dB 9 dB 25 dB 25 dB 17 dB 1.0 dB 1.0 dB 25 dB 25 dB 15 dB 1.0 dB 1.0 dB 20 dB 20 dB 11 dB 1.0 dB 1.0 dB 15 dB 15 dB 9 dB 1.0 dB 1.0 dB 8.5 GHz to 11 GHz to 11 GHz 20 GHz 15 dB 15 dB 8 dB 1.0 dB 1.0 dB 15 dB 15 dB 7 dB 1.0 dB 1.0 dB Source match 20 dB Transmission 1.0 dB tracking Reflection tracking 1.0 dB www..com 13 Test Port Output (Source) Test port output frequency Table 11. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485/2D5/2K5/4D5/4K5 Description Frequency range Option 230/430 Option 240/440 Option 260/460 Option 280/480 Option 235/435 Option 245/445 Option 265/465 Option 285/485 Option 2D5/4D5 Option 2K5/4K5 Resolution Source stability standard Option 1E5 CW accuracy standard Option 1E5 Specification 9 kHz to 3 GHz 9 kHz to 4.5 GHz 9 kHz to 6.5 GHz 9 kHz to 8.5 GHz 100 kHz to 3 GHz 100 kHz to 4.5 GHz 100 kHz to 6.5 GHz 100 kHz to 8.5 GHz 300 kHz to 14 GHz 300 kHz to 20 GHz 1 Hz Typical 5 ppm (5 to 40 C) 0.05 ppm (5 to 40 C), 0.5 ppm/year 5 ppm 1 ppm www..com 14 Test port output power1 Table 12. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Nominal power (preset power) Level accuracy2, 6 (stepped sweep mode) Level accuracy2 (swept sweep mode) Level linearity3, 5, 6 (stepped sweep mode) 9 kHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8.5 GHz Level linearity5 (swept sweep mode)4 9 kHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8.5 GHz Range5, 6 9 kHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8.5 GHz Sweep range5, 6 9 kHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8.5 GHz Level resolution -55 to 10 dBm -55 to 9 dBm -55 to 8 dBm -55 to 7 dBm -55 to 10 dBm -55 to 9 dBm -55 to 8 dBm -55 to 7 dBm 0.05 dB Specification 0 dBm 0.650 dB (at 0 dBm, 50 MHz absolute) 1.0 dB Typical 2.5 dB 0.75 dB (-20 to 10 dBm) 0.75 dB (-20 to 9 dBm ) 0.75 dB (-20 to 8 dBm ) 0.75 dB (-20 to 7 dBm ) 1.5 dB (at -20 to 10 dBm) 1.5 dB (at -20 to 9 dBm) 1.5 dB (at -20 to 8 dBm) 1.5 dB (at -20 to 7 dBm) Description Max leveled (Option 230/235/240/245/260/ 265/280/285) 9 kHz to 8.5 GHz (Option 430/435/440/445/460/ 465/480/485) 9 kHz to 6 GHz 6 GHz to 7 GHz www..com 7 GHz to 8.5 GHz 1. 2. 3. 4. 5. 6. Specification SPD power5, 6 10 dBm 10 dBm 9 dBm 8 dBm Source output performance on port 1 only. Other port output performance is typical. Level accuracy is taken at 0 dBm, relative to 50 MHz reference unless otherwise stated. Level linearity given is relative to 0 dBm. The specification might not be met at 5 MHz or 50 MHz. The level accuracy specification needs to be taken into account for test port output power level. Power calibration using an external power meter improves level accuracy of the test port output power. Proper power meters/sensors, and the 82357B USB-GPIB interface are required to conduct power calibration. 15 Test port output power7 (continued) Table 13. Option 2D5/2K5/4D5/4K5 Description Nominal power (preset power) Level accuracy6 (stepped sweep mode)1 300 kHz to 1 MHz 1 MHz to 5 MHz 5 MHz to 8.5 GHz 8.5 GHz to 20 GHz Level accuracy (swept sweep mode)2 300 kHz to 1 GHz 1 GHz to 8.5 GHz 8.5 GHz to 20 GHz Level linearity5, 6 (stepped sweep mode)3 300 kHz to 1 MHz 1 MHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz Level linearity5 (swept sweep mode)3 300 kHz to 1 MHz 1 MHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz Range5, 6 300 kHz to 1 MHz 1 MHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz Sweep range4, 5, 6 300 kHz to 1 MHz 1 MHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10.5 GHz 10.5 GHz to 15 GHz 15 GHz to 20 GHz (Source attenuator www..com = 0 dB) Level resolution 1. 2. 3. 4. 5. 6. Specification -5 dBm 0.650 dB +2.0 dB, -6.0 dB 2.0 dB 1.0 dB 2.5 dB Typical 5.0 dB 2.5 dB +5.0 dB, -7.0 dB 0.75 dB (-25 to 8 dBm) 0.75 dB (-25 to 10 dBm) 0.75 dB (-25 to 9 dBm ) 0.75 dB (-25 to 7 dBm ) 0.75 dB (-25 to 3 dBm ) 0.75 dB (-25 to 0 dBm ) 1.5 dB (-25 to 8 dBm) 1.5 dB (-25 to 10 dBm) 1.5 dB (-25 to 9 dBm ) 1.5 dB (-25 to 7 dBm ) 1.5 dB (-25 to 3 dBm ) 1.5 dB (-25 to 0 dBm ) -85 to 8 dBm -85 to 10 dBm -85 to 9 dBm -85 to 7 dBm -85 to 3 dBm -85 to 0 dBm -25 to 8 dBm -25 to 10 dBm -25 to 9 dBm -25 to 7 dBm -25 to 3 dBm -25 to 0 dBm 0.05 dB Level accuracy is taken at -5 dBm, relative to 50 MHz reference unless otherwise stated. Level accuracy is taken at -5 dBm, relative to 50 MHz reference. Level linearity given is relative to -5 dBm. The sweep range shifts based on the selected source attenuator value (0 dB to 60 dB, 10 dB step). The level accuracy specification needs to be taken into account for test port output power level. Power calibration using an external power meter improves level accuracy of the test port output power. Proper power meters/sensors, and the 82357B USB-GPIB interface are required to conduct power calibration. 7. Source output performance on port 1 only. Other port output performance is typical. 16 Test port output power6 (continued) Table 13. Option 2D5/2K5/4D5/4K5 Description Max leveled 300 kHz to 1 MHz 1 MHz to 10 GHz 10 GHz to 13 GHz 13 GHz to 15 GHz 15 GHz to 18 GHz 18 GHz to 20 GHz power3, 4 9 dBm 10 dBm 9 dBm 7 dBm 5 dBm 4 dBm Specification SPD Test port output signal purity Table 14. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Harmonics (2nd or 3rd) 9 kHz to 2 GHz 2 GHz to 8.5 GHz Non-harmonic spurious 9 kHz to 8.5 GHz Specification Typical < -25 dBc (at 5 dBm) < -20 dBc (at 5 dBm) < -30 dBc (at 5 dBm) Table 15. Option 2D5/2K5/4D5/4K5 Description Harmonics (2nd to 300 kHz to 1 GHz 1 GHz to 20 GHz Non-harmonic spurious2 300 kHz to 20 GHz 5th)1 < -12 dBc (at maximum output power)5 < -15 dBc (at maximum output power)5 < -30 dBc (at -5 dBm) Specification Typical www..com This includes 6th and 7th harmonics when the test frequency is from 1 MHz to 1 GHz. The carrier 1/8th spurious is excluded from 8.76 GHz to 17.52 GHz. The level accuracy specification needs to be taken into account for test port output power level. Power calibration using an external power meter improves level accuracy of the test port output power. Proper power meters/sensors, and the 82357B USB-GPIB interface are required to conduct power calibration. 5. Maximum output power is the maximum power of "Range" in Table 13 Test port output power. 6. Source output performance on port 1 only. Other port output performance is typical. 1. 2. 3. 4. 17 Test Port Input Test port input levels Table 16. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Maximum test port input level 9 kHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8.5 GHz Damage level 9 kHz to 8.5 GHz Crosstalk1 9 kHz to 300 kHz 300 kHz to 10 MHz 10 MHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz -100 dB -110 dB -120 dB -110 dB -100 dB +26 dBm 35 VDC +10 dBm +9 dBm +8 dBm +7 dBm Specification Typical Description Test port noise floor 9 kHz to 10 MHz 10 MHz to 5 GHz 5 GHz to 6 GHz 6 GHz to 7 GHz 7 GHz to 8 GHz 8 GHz to 8.5 GHz Specification SPD -115 dBm/Hz -130 dBm/Hz -131 dBm/Hz -130 dBm/Hz -129 dBm/Hz -127 dBm/Hz www..com 1. The specification might not be met at 5 MHz or 50 MHz. 18 Test port input levels (continued) Table 17. Option 2D5/2K5/4D5/4K5 Description Maximum test port input level 300 kHz to 20 GHz Damage level 300 kHz to 20 GHz Crosstalk1 300 kHz to 1 MHz 1 MHz to 5 MHz 5 MHz to 10 MHz 10 MHz to 45 MHz 45 MHz to 4 GHz 4 GHz to 6 GHz 6 GHz to 8.5 GHz 8.5 GHz to 15 GHz 15 GHz to 20 GHz -68 dB -70 dB -100 dB -110 dB -118 dB -123 dB -120 dB -112 dB -106 dB +26 dBm or 35 VDC +10 dBm Specification Typical Description Test port noise floor 300 kHz to 1 MHz 1 MHz to 10 MHz 10 MHz to 100 MHz 100 MHz to 8.5 GHz 8.5 GHz to 15 GHz 15 GHz to 20 GHz Specification SPD -110 dBm/Hz -115 dBm/Hz -129 dBm/Hz -130 dBm/Hz -118 dBm/Hz -115 dBm/Hz www..com 1. The specification might not be met at 5 MHz or 50 MHz. 19 Test port input (trace noise) Table 18. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Compression level Magnitude 9 kHz to 5 GHz 5 GHz to 8.5 GHz (maximum test port input level = +10 dBm) Phase 9 kHz to 3 GHz 3 GHz to 5 GHz 5 GHz to 8.5 GHz (maximum test port input level = +10 dBm) Trace noise magnitude1 9 kHz to 30 kHz (IFBW = 3 kHz) (maximum test port input level = +10 dBm) 30 kHz to 100 kHz (IFBW = 3 kHz) (maximum test port input level = +10 dBm) 100 kHz to 10 MHz (IFBW = 3 kHz) (maximum test port input level = +10 dBm) 10 MHz to 4.38 GHz (IFBW = 70 kHz) (maximum test port input level = +10 dBm) 4.38 GHz to 5 GHz (IFBW = 70 kHz) (maximum test port input level = +10 dBm) 5 GHz to 6 GHz (IFBW = 70 kHz) (maximum test port input level = +9 dBm) 6 GHz to 7 GHz (IFBW = 70 kHz) (maximum test port input level = +8 dBm) 7 GHz to 8.5 GHz (IFBW = 70 kHz) (maximum test port input level = +7 dBm) Trace noise phase2 9 kHz to 30 kHz (IFBW = 3 kHz) (maximum test port input level = +10 dBm) 30 kHz to 10 MHz (IFBW = 3 kHz) (maximum test port input level = +10 dBm) 10 MHz to 4.38 GHz (IFBW = 70 kHz) (maximum test port input level = +10 dBm) 4.38 GHz to 5 GHz (IFBW = 70 kHz) (maximum test port input level = +10 dBm) 5 GHz to 6 GHz (IFBW = 70 kHz) (maximum test port input level = +9 dBm) 6 GHz to 7 GHz (IFBW = 70 kHz) (maximum test www..comport input level = +8 dBm) 7 GHz to 8.5 GHz (IFBW = 70 kHz) (maximum test port input level = +7 dBm) 0.035 deg rms 0.020 deg rms 0.035 deg rms 0.050 deg rms 0.050 deg rms 0.050 deg rms 0.050 deg rms 0.004 dBrms 0.003 dBm 0.003 dBrms 0.004 dBrms 0.006 dBrms 0.006 dBrms 0.006 dBrms 0.006 dBrms 0.001 dBm 0.001 dBm 0.0005 dBm 0.001 dBrms 0.0012 dBm 0.0012 dBm 0.0012 dBm 0.0012 dBm 0.08 dB 0.1 dB Specification SPD 0.3 deg 0.6 deg 1.0 deg 1. The specification might not be met at the following frequencies: 333.333 kHz, 406.25 kHz, 857.143 kHz, 928.571 kHz, 1.3 MHz, 2.4 MHz and 4.333333 MHz. 2. The specification might not be met at 5 MHz or 50 MHz. 20 Test port input (trace noise) (continued) Table 19. Option 2D5/2K5/4D5/4K5 Description Compression level Magnitude 300 kHz to 10 MHz 10 MHz to 10 GHz 10 GHz to 15 GHz 15 GHz to 20 GHz (maximum test port input level = +10 dBm) Phase 300 kHz to 5 GHz 5 GHz to 10 GHz 10 GHz to 15 GHz 15 GHz to 20 GHz (maximum test port input level = +10 dBm) Trace noise magnitude1, 3 300 kHz to 1 MHz (IFBW = 3 kHz) 1 MHz to 10 MHz (IFBW = 3 kHz) 10 MHz to 4.38 GHz (IFBW = 70 kHz) 4.38 GHz to 8.5 GHz (IFBW = 70 kHz) 8.5 GHz to 13.137 GHz (IFBW = 70 kHz) 13.137 GHz to 17 GHz (IFBW = 70 kHz) 17 GHz to 20 GHz (IFBW = 70 kHz) (at maximum output power level of sweep range) Trace noise phase2, 3 300 kHz to 1 MHz (IFBW = 3 kHz) 1 MHz to 10 MHz (IFBW = 3 kHz) 10 MHz to 4.38 GHz (IFBW = 70 kHz) 4.38 GHz to 8.5 GHz (IFBW = 70 kHz) 8.5 GHz to 13.137 GHz (IFBW = 70 kHz) 13.137 GHz to 17 GHz (IFBW = 70 kHz) 17 GHz to 20 GHz (IFBW = 70 kHz) (at maximum output power level www..com of sweep range) 0.040 deg rms 0.020 deg rms 0.035 deg rms 0.050 deg rms 0.064 deg rms 0.095 deg rms 0.165 deg rms 0.0120 deg rms 0.0025 deg rms 0.0075 deg rms 0.0150 deg rms 0.0250 deg rms 0.0320 deg rms 0.0520 deg rms 0.006 dBrms 0.003 dBrms 0.004 dBrms 0.006 dBrms 0.009 dBrms 0.013 dBrms 0.023 dBrms 0.0009 dBrms 0.0005 dBrms 0.0010 dBrms 0.0012 dBrms 0.0024 dBrms 0.0040 dBrms 0.0065 dBrms 2.3 deg 4.3 deg 17.3 deg 20.3 deg 0.3 dB 0.182 dB 0.712 dB 1.87 dB Specification SPD 1. The specification might not be met at the following frequencies: 406.25 kHz, 666.667 kHz, 722.222 kHz, 857.143 kHz, 928.571 kHz, 1.444444 MHz, 1.714286 MHz, 1.8 MHz, 1.857143 MHz, 1.95 MHz, 2.4375 MHz, 2.571429 MHz, 3.714286 MHz, 4.8 MHz, 5 MHz, 5.416667 MHz, 7.583333 MHz, 10 MHz, 10.833333 MHz, 12.5 MHz. 2. The specification might not be met at 5 MHz or 50 MHz. 3. Trace noise SPD is defined with transmission measurements only. 21 Test port input (stability)1 Table 20. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Stability magnitude 9 kHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Stability phase 9 kHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz 0.1 deg/C 0.2 deg/C 0.8 deg/C 0.005 dB/C 0.01 dB/C 0.04 dB/C Specification Typical Table 21. Option 2D5/2K5/4D5/4K5 Description Stability magnitude 300 kHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 20 GHz Stability phase 300 kHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 20 GHz 0.1 deg/C 0.2 deg/C 0.8 deg/C 0.005 dB/C 0.01 dB/C 0.04 dB/C Specification Typical www..com 1. Stability is defined as a ratio measurement at the test port. 22 Test port input (dynamic accuracy) Table 22. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Accuracy of the test port input power reading is relative to -10 dBm reference input power level. Description Dynamic accuracy magnitude 10 dBm -30 dBm -100 dBm Dynamic accuracy phase 10 dBm -30 dBm -100 dBm 5 deg 0.3 deg 15.1 deg 0.21 dB 0.05 dB 2.01 dB Specification Typical Specification Magnitude 10 Typical Phase 100 1 Accuracy [degrees] 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 Accuracy [dB] 10 0.1 1 0.01 0.1 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 Test port power [dBm] 3.0 dB (at -110 dBm, Ref.= -10 dBm, typical) Test port power [dBm] www..com 23 Test port input (dynamic accuracy) (continued) Table 23. Option 2D5/2K5/4D5/4K5 Accuracy of the test port input power reading is relative to -10 dBm reference input power level. Description Dynamic accuracy magnitude 10 dBm -30 dBm -100 dBm Dynamic accuracy phase 10 dBm -30 dBm -100 dBm 20.66 deg 0.3 deg 15.1 deg 2.4972 dB 0.05 dB 2.01 dB Specification Typical Specification Typical Magnitude 10 Phase 100 Accuracy [degrees] Accuracy [dB] 1 10 0.1 1 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 0.1 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 Test port power [dBm] Test port power [dBm] 3.0 dB (at -110 dBm, Ref.= -10 dBm, typical) www..com 24 Test port input (group delay)1 Table 24. Option 230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485 Description Aperture (selectable) Maximum aperture Minimum delay Specification (frequency span)/(number of points - 1) 25% of frequency span Supplemental information Limited to measuring no more than 180 C of phase change within the minimum aperture. See graph below, typical Accuracy The following graph shows group delay accuracy with type-N connectors, full 2-port calibration and a 10 Hz IF bandwidth. Calibration kit (85032F). Insertion loss is assumed to be < 2 dB. 100 10 Accuracy (nSec) 1 0.1 0.01 0.001 0.01 0.1 1 10 100 Aperture (MHz) In general, the following formula can be used to determine the accuracy, in seconds, of a specific group delay measurement: phase accuracy (degrees) / [360 x aperture (Hz)] www..com 1. Group delay is computed by measuring the phase change within a specified step (determined by the frequency span and the number of points per sweep). 25 Test port input (group delay)1 (continued) Table 25. Option 2D5/2K5/4D5/4K5 Description Aperture (selectable) Maximum aperture Minimum delay Specification (frequency span)/(number of points - 1) 25% of frequency span Supplemental information Limited to measuring no more than 180 C of phase change within the minimum aperture. See graph below, typical Accuracy The following graph shows group delay accuracy with 3.5 mm (male) connectors, full 2-port calibration and a 10 Hz IF bandwidth. Calibration kit (85052D). Insertion loss is assumed to be < 2 dB. 100 10 Accuracy (nSec) 1 0 .1 0 .0 1 Frequency = 1 G H z C al pow er = -10 dBm ; M eas pow er = -10 dBm ; Electrical Length = 10 m 0 .0 0 1 0 .0 1 0 .1 1 10 100 Aperture (MHz) In general, the following formula can be used to determine the accuracy, in seconds, of a specific group delay measurement: phase accuracy (degrees) / [360 x aperture (Hz)] www..com 1. Group delay is computed by measuring the phase change within a specified step (determined by the frequency span and the number of points per sweep). 26 General Information Table 26. System bandwidth Description IF bandwidth settings Range 10 Hz to 500 kHz Nominal settings are: 10, 15, 20, 30, 40, 50, 70, 100, 150, 200, 300, 400, 500, 700, 1 k, 1.5 k, 2 k, 3 k, 4 k, 5 k, 7 k, 10 k, 15 k, 20 k, 30 k, 40 k, 50 k, 70 k, 100 k, 150 k, 200 k, 300 k, 400 k, 500 kHz General characteristics Table 27. Front panel information Description RF connectors Option 230/235/240/ 245/260/265/280/285/ 430/435/440/445/460/ 465/480/485 Option 2D5/2K5/4D5/4K5 Probe power Connector Voltage & maximum current +15 V 2% (400 mA) -12.6 V 5% (300 mA) (Combined load for both probe connections) 10.4 in TFT color LCD with touch screen XGA (1024 x 768)1 3 terminal connector x 2 Type-N, female, 50 Typical General characteristics 3.5 mm (male), 50 nominal Display Type Resolution www..com 1. Valid pixels are 99.99 % and more. Below 0.01 % (approx. 30 points) of fixed points of black, blue, green or red are not regarded as failure. 27 Table 28. Rear panel information Description Type Input level Typical General characteristics BNC, female Low threshold voltage: 0.5 V High threshold voltage: 2.1 V Input level range: 0 to + 5 V External trigger input connector Pulse width Polarity External trigger output connector Type Maximum output current Output level Pulse width Polarity External reference signal input connector Type Input frequency Input level 10 MHz 10 ppm -3 to + 10 dBm 2 sec Positive or negative BNC, female 50 mA Low level voltage: 0 V High level voltage: 5 V 1 sec Positive or negative BNC, female Internal reference signal output connector Type Output frequency Signal type Output level Output impedance Internal reference signal oven connector Type Output frequency Output level 10 MHz 1 ppm 0 dBm minimum BNC, female 10 MHz 5 ppm Sinewave 0 dBm 3 dB into 50 50 BNC, female www..com 28 Table 28. Rear panel information (continued) Description Bias tee input connector Type Maximum voltage Maximum current (no degradation in RF specifications) Option 230/235/240/245/260/265/280/ 285/430/435/440/445/460/465/480/485 50 mA (1 MHz < test frequency < 500 MHz) 200 mA (test frequency 1 MHz, 500 MHz) Option 2D5/2K5/4D5/4K5 Maximum current (damage level) Fuse Video output 200 mA 500 mA 500 mA, bi-pin style 15-pin mini D-Sub; female; drives XGA compatible monitors 24-pin D-Sub (Type D-24), female; compatible with IEEE-488 Universal serial bus jack, Type A configuration (4 contacts inline, contact 1 on left); female; provides connection to printer, ECal module, USB/GPIB interface or multiport test set Contact 1 Contact 2 Contact 3 Contact 4 Vcc: 4.75 to 5.25 VDC, 500 mA, maximum - Data + Data Ground BNC, female (for each port) 35 VDC Typical General characteristics GPIB USB-host port www..com 29 Table 28. Rear panel information (continued) Description USB (USBTMC1) interface port Typical General characteristics Universal serial bus jack, Type B configuration (4 contacts inline); female; provides connection to an external PC; compatible with USBTMC-USB488 and USB 2.0. 10/100BaseT Ethernet, 8-pin configuration; auto selects between the two data rates 36-pin centronics, female; provides connection to handler system LAN Handler I/O port Line power2 Frequency Voltage 47 Hz to 63 Hz 90 to 132 VAC, or 198 to 264 VAC (automatically switched) 350 VA max. VA max Description AUX input connector Type Input range Accuracy Specification General characteristics BNC, female x 2 1 V or 10 V selectable 1 % + 1 mV for 1 V input 1 % + 10 mV for 10 V input Table 29. LXI compliance Description General characteristics Class C (only applies to units that are shipped with firmware revision A.08.00 or later) www..com 1. USB Test and Measurement Class (TMC) interface that communicates over USB, complying with the IEEE 488.1 and IEEE 488.2 standards. 2. A third-wire ground is required. 30 Table 30. EMC, safety and environment Description EMC European Council Directive 2004/108/EC IEC 61326-1:2005 EN 61326-1:2006 CISPR 11:2003+A1:2004 EN 55011:2007 Group 1, Class A IEC 61000-4-2:1995 +A2:2000 EN 61000-4-2:1995 +A2:2001 4 kV CD / 8 kV AD IEC 61000-4-3:2006 EN 61000-4-3:2006 1-3 V/m, 80-1000 MHz / 1.4 GHz - 2.7 GHz, 80% AM IEC 61000-4-4:2004 EN 61000-4-4:2004 1 kV power lines / 0.5 kV signal lines IEC 61000-4-5:2005 EN 61000-4-5:2006 0.5 kV line-line / 1 kV line-ground IEC 61000-4-6:2003 + A1:2004+ A2:2006 EN 61000-4-6:2007 3 V, 0.15-80 MHz, 80% AM IEC 61000-4-11:2004 EN 61000-4-11:2004 0.5-300 cycle, 0% / 70% ICES-001:2006 Group 1, Class A AS/NZS CISPR11:2004 Group 1, Class A Safety European Council Directive 2006/95/EC IEC 61010-1:2001 / EN 61010-1:2001 Measurement Category I Pollution Degree 2 Indoor Use CAN/CSA C22.2 No. 61010-1-04 Measurement Category I Pollution Degree 2 Indoor Use Environment This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product/ for more information. General characteristics www..com 31 Table 31. Analyzer environmental specifications and dimensions Description Operating environment Temperature Error-corrected temperature range Humidity Altitude Vibration Non-Operating storage environment Temperature Humidity Altitude Vibration Dimensions Weight (net) Option 230/240/260/280 (2-port) Option 235/245/265/285 (2-port) Option 430/480/440/460 (4-port) Option 435/445/465/485 (4-port) Option 2D5/2K5 (2-port) Option 4D5/4K5 (4-port) -10 C to +60 C 20% to 90% at wet bulb temperature < +40 C (non-condensation) 0 to 4572 m (0 to 15,000 feet) 0.5 G maximum, 5 Hz to 500 Hz See next page. 18.2 kg 18.3 kg 19.9 kg 20.0 kg 19.8 kg 21.8 kg +5 C to +40 C 23 C (5 C) with < 1 C deviation from calibration temperature 20% to 80% at wet bulb temperature < +29 C (non-condensation) 0 to 2,000 m (0 to 6561 feet) 0.21 G maximum, 5 Hz to 500 Hz General characteristics www..com 32 426 22 27 58 19 20 51 122 37 Figure 3. Dimensions (front view, E5071C with Option 230/235/240/245/260/265/280/285, in millimeters) 426 22 22 27 58 19 20 51 41 41 41 37 www..com (front view, E5071C with Option 430/435/440/445/460/465/480/485, Figure 4. Dimensions in millimeters) 33 22 222 222 426 22 27 19 58 20 51 122 37 Figure 5. Dimensions (front view, E5071C with Option 2D5/2K5, in millimeters) Figure 6. Dimensions (front view, E5071C with Option 4D5/4K5, in millimeters) www..com 34 26 222 1 424 422 128 1 96 21 18 27 148 25 109 25 25 290 25 25 25 165 Figure 7. Dimensions (rear view with Option 1E5, in millimeters) 472 32 417 23.4 222 25 58 235 Figure 8. Dimensions (side view, E5071C Option 230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485, in millimeters) 472 32 417 23 222 13 15 www..com 235 13 14 Figure 9. Dimensions (side view, E5071C with Option 2D5/2K5/4D5/4K5, in millimeters) 35 18 215 18 215 144 146 159 179 190 215 Measurement Throughput Summary Cycle time for measurement completion1, 2 (ms) Table 32. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF Number of points 51 Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal Uncorrected 2-port cal 4-port cal Uncorrected 2-port cal 4-port cal Uncorrected 2-port cal 4-port cal 3.4 6.3 13 3.7 6.6 13 54 107 213 8.7 17 34 4.9 9.3 19 5.2 10 21 202 401 800 11 21 42 7.1 14 28 7.3 15 32 397 792 1581 12 24 49 20 41 92 20 42 94 1563 3125 6247 25 48 102 201 401 1601 Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidth Start 1 GHz, stop 1.2 GHz, 1 kHz IF bandwidth Start 100 kHz, stop 3 GHz, 500 kHz IF bandwidth Start 100 kHz, stop 3 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 8.8 17 34 11 22 42 13 24 49 26 54 118 Start 100 kHz, stop 3 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal www..com 56 112 222 206 410 818 404 805 1608 1583 3163 6324 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 36 Table 32. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 (continued) Number of points 51 Start 100 kHz, stop 8.5 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 15 28 55 18 35 69 19 38 74 24 48 104 201 401 1601 Start 100 kHz, stop 8.5 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 15 28 56 18 36 70 20 38 75 26 52 117 Start 100 kHz, stop 8.5 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 57 114 225 207 412 821 404 806 1611 1583 3163 6324 www..com 37 Cycle time for measurement completion1, 2 (ms) Table 33. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON Number of Points 51 Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.5 6.4 13 5.5 9.8 20 8.0 15 29 24 49 108 201 401 1601 Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.6 6.6 13 5.4 11 22 8.0 16 33 23 48 107 Start 1 GHz, stop 1.2 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 54 107 213 202 401 800 397 792 1581 1563 3125 6247 Start 100 kHz, stop 3 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 8.7 18 34 11 21 42 13 24 49 28 53 112 Start 100 kHz, stop 3 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 8.8 17 34 11 22 42 13 25 50 28 57 122 Start 100 kHz, stop 3 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 56 112 222 206 410 818 404 805 1608 1583 3163 6324 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 38 Table 33. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 (continued) Number of points 51 Start 100 kHz, stop 8.5 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 15 28 55 18 35 69 20 38 74 27 52 111 201 401 1601 Start 100 kHz, stop 8.5 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal Uncorrected 2-port cal 4-port cal 15 28 56 57 114 225 18 36 70 207 412 821 20 38 75 404 806 1611 27 56 120 1583 3163 6324 Start 100 kHz, stop 8.5 GHz, 1 kHz IF bandwidth www..com 39 Cycle time for measurement completion1, 2 (ms) Table 34. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Sweep mode: Stepped, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON Number of Points 51 Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 4.4 8.2 16 7.7 15 29 12 22 45 29 56 126 201 401 1601 Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 4.8 9.0 18 9.2 18 35 15 28 56 41 80 163 Start 1 GHz, stop 1.2 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 54 107 213 202 401 800 397 792 1581 1563 3125 6247 Start 100 kHz, stop 3 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 6.7 13 26 13 24 47 18 36 70 48 94 190 Start 100 kHz, stop 3 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 7.1 14 27 14 27 53 22 42 82 60 119 237 Start 100 kHz, stop 3 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 56 112 222 206 410 818 404 805 1608 1583 3163 6324 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 40 Table 34. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 (continued) Number of points 51 Start 100 kHz, stop 8.5 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 7.5 15 29 13 26 50 19 37 73 48 94 189 201 401 1601 Start 100 kHz, stop 8.5 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 7.9 16 30 15 29 56 22 43 85 60 120 237 Start 100 kHz, stop 8.5 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 57 114 225 207 412 821 404 806 1611 1583 3163 6324 www..com 41 Cycle time for measurement completion1, 2 (ms) Table 35. Option 2D5/2K5/4D5/4K5 Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF Number of points 51 Start 300 kHz, stop 20 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 23 45 88 36 71 142 39 77 155 43 85 169 201 401 1601 Start 300 kHz, stop 20 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 23 45 89 37 72 144 40 78 156 43 86 171 Start 300 kHz, stop 20 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 60 120 237 212 421 840 410 817 1632 1591 3180 6358 Start 8 GHz, stop 18 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 17 34 67 22 42 83 22 44 86 23 45 102 Start 8 GHz, stop 18 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 18 34 67 22 42 84 23 44 87 24 47 106 Start 8 GHz, stop 18 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 58 115 229 207 413 823 405 807 1612 1583 3163 6324 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 42 Table 35. Option 2D5/2K5/4D5/4K5 (continued) Number of points 51 Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.0 5.6 11 3.2 6.1 14 4.9 9.9 23 17 37 84 201 401 1601 Start 11 GHz, stop 12 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.0 5.6 11 3.4 6.4 14 5.5 11 24 18 38 85 Start 11 GHz, stop 12 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 52 104 206 200 399 795 396 790 1578 1566 3130 6258 www..com 43 Cycle time for measurement completion1, 2 (ms) Table 36. Option 2D5/2K5/4D5/4K5 Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON Number of points 51 Start 300 kHz, stop 20 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 23 45 88 36 71 142 39 77 155 43 85 170 201 401 1601 Start 300 kHz, stop 20 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 23 45 89 37 72 144 40 78 156 43 86 171 Start 300 kHz, stop 20 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 60 120 237 212 421 840 410 817 1632 1591 3180 6358 Start 8 GHz, stop 18 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 17 34 67 22 42 83 22 44 86 23 48 107 Start 8 GHz, stop 18 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 18 34 67 22 42 83 23 44 87 24 49 110 Start 8 GHz, stop 18 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 58 115 229 207 413 823 405 807 1612 1583 3163 6324 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 44 Table 36. Option 2D5/2K5/4D5/4K5 (continued) Number of points 51 Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.0 5.6 11 3.4 6.6 14 5.9 12 26 20 43 98 201 401 1601 Start 11 GHz, stop 12 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.0 5.6 11 3.5 6.8 15 5.8 12 26 20 43 98 Start 11 GHz, stop 12 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 52 104 206 200 399 795 396 790 1578 1566 3130 6258 www..com 45 Cycle time for measurement completion1, 2 (ms) Table 37. Option 2D5/2K5/4D5/4K5 Sweep mode: Stepped, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON Number of points 51 201 401 1601 Start 300 kHz, stop 20 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 11 21 41 18 35 69 24 48 94 56 112 222 Start 300 kHz, stop 20 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 11 22 42 20 38 75 28 54 107 69 137 272 Start 300 kHz, stop 20 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 60 120 237 212 421 840 410 817 1632 1591 3180 6358 Start 8 GHz, stop 18 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 8.4 17 32 14 27 52 19 38 74 48 94 188 Start 8 GHz, stop 18 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 8.8 17 34 15 30 58 22 44 86 60 120 237 Start 8 GHz, stop 18 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal www..com 58 115 229 207 413 823 405 807 1612 1583 3163 6324 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 46 Table 37. Option 2D5/2K5/4D5/4K5 (continued) Number of points 51 Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 2.8 5.1 9.6 6.4 13 24 11 21 41 31 61 131 201 401 1601 Start 11 GHz, stop 12 GHz, 100 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 3.4 5.9 12 8.0 16 30 14 27 53 43 86 171 Start 11 GHz, stop 12 GHz, 1 kHz IF bandwidth Uncorrected 2-port cal 4-port cal 52 104 206 200 399 795 396 790 1578 1566 3130 6258 www..com 47 Cycle time (ms)1, 2 vs. number of points Table 38. Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth, error correction: OFF, display update: OFF, number of traces = 1 Number of points 3 11 51 101 201 401 801 1601 Sweep mode: Fast swept, system error correction: OFF 3.1 3.3 3.5 3.9 4.9 7.1 12 20 Sweep mode: Fast swept, system error correction: ON 3.1 3.3 3.5 4.1 5.5 8.0 14 24 Sweep mode: Std stepped, system error correction: ON 3.4 3.3 4.4 5.6 7.7 12 18 29 Cycle time (ms)1, 2 vs. number of points Table 39. Option 2D5/2K5/4D5/4K5 Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidth, error correction: OFF, display update: OFF, number of traces = 1 Number of points 51 201 401 1601 Sweep mode: Fast swept, system error correction: OFF 3.0 3.2 4.9 17 Sweep mode: Fast swept, system error correction: ON 3.0 3.4 5.9 20 Sweep mode: Std stepped, system error correction: ON 2.8 6.5 11 31 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 48 Cycle time (ms)1, 2 vs. IF bandwidth Table 40. All options Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF, NOP = 201 Option 230/235/240/245/260/265/280/ 285/430/435/440/445/460/465/480/485 Frequency [Hz] 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G 4G Option 2D5/2K5/4D5/4K5 Frequency [Hz] 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G 10 G IFBW [Hz] 500000 400000 300000 200000 150000 100000 70000 50000 40000 30000 20000 15000 10000 7000 5000 4000 3000 2000 1500 1000 700 500 400 300 200 150 100 Cycle time [ms] 5.0 5.0 4.9 4.9 4.9 5.0 5.7 6.9 7.8 9.4 13 16 23 31 42 52 68 100 133 198 278 391 487 648 970 1291 1935 2739 3864 4829 6437 9653 12870 19302 IFBW [Hz] 500000 400000 300000 200000 150000 100000 70000 50000 40000 30000 20000 15000 10000 7000 5000 4000 3000 2000 1500 1000 700 500 400 300 200 150 100 70 50 40 30 20 15 10 49 Cycle time [ms] 2.8 2.8 2.8 2.8 2.8 3.0 3.8 4.9 5.9 7.5 11 14 21 29 40 50 66 98 132 196 276 389 485 646 968 1289 1933 2739 3869 4837 6449 9671 12892 19330 4G 70 www..com 4G 50 4G 4G 4G 4G 4G 40 30 20 15 10 1. Supplemental performance data. 2. Measured with firmware version A.09.30. Data transfer time1, 2 (ms) Table 41. All options Number of points 51 SCPI over GPIB3 4 3 30 1 1 15 12 7 108 1 1 59 25 13 223 2 1 117 88 45 841 4 2 457 64-bit floating point 32-bit floating point ASCII SCPI over 100 Mbps LAN (Telnet)3 REAL 64 REAL 32 ASCII 201 401 1601 SCPI over 100 Mbps LAN (SICL-LAN)3 REAL 64 REAL 32 ASCII SCPI over USB REAL 64 REAL 32 ASCII SCPI over GPIB/USB (82357B) REAL 64 REAL 32 ASCII COM4 Variant type 1 1 1 1 8 7 75 15 10 290 21 13 579 68 37 2313 (SICL-USB)3 2 2 4 2 2 13 2 2 24 3 3 91 3 3 4 3 3 8 4 3 14 6 5 47 www..com 1. Supplemental performance data. 2. Measured with firmware version A.09.30. 3. Measured using a VEE Pro 7.0 program running on a 3.2 GHz Pentium 4 DELL Precision 370, Transferred complex S11 data, using :CALC{1-36}:DATA:FDAT?. 4. Measured using an E5071C VBA macro running inside the analyzer. Transferred complex S11 data. 50 E5091A Multiport Test Set The section provides port performance of test set without calibration. Table 42. Test set input/output performance Description Range Damage level Specification 50 MHz to 8.5 GHz Typical 20 dBm, 25 VDC (typical) Table 43. Option E5091A-009 port performance Specification 50 MHz to 300 MHz 300 MHz to 1.3 GHz 1.3 GHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Description Load match Test port selected A, T2, R1+, R1- T1, R2+, R2-, R3+, R3- Test port unselected 19 dB 15 dB 20 dB 17 dB 25 dB 20 dB 19 dB 18 dB 15 dB 19 dB 16 dB 17 dB 12 dB 11 dB 12 dB 12 dB 13 dB 10 dB 8 dB 11 dB 9 dB 9 dB A, T2, R1+, R1-, R3+, R3- 23 dB T1, R2+, R2- Interconnect port, typical P1, P2, P3, P4 Insertion loss Test port A, T2, R1+, R1- T1, R2+, R2-, R3+, R3- Stability, typical Isolation Over arbitrarily test ports -100 dB 3 dB 5 dB 0.005 dB/ C 19 dB 18 dB 3 dB 5 dB 0.005 dB/ C -100 dB 4 dB 7 dB 0.005 dB/ C -100 dB 5 dB 8 dB 0.01 dB/ C -100 dB 6 dB 9.5 dB 0.015 dB/ C -90 dB www..com 51 Table 44. Option E5091A-016 port performance Specification 50 MHz to 300 MHz 300 MHz to 1.3 GHz 1.3 GHz to 3 GHz 3 GHz to 6 GHz 6 GHz to 8.5 GHz Description Load match Test port selected A, T4, R1+, R1-, R2+, R2-, 15 dB R3+, R3-, R4+, R4- T1, T2, T3 12 dB 17 dB 14 dB 20 dB 15 dB 12 dB 15 dB 14 dB 16 dB 14 dB 12 dB 9 dB 8 dB 10 dB 8 dB 9 dB 8 dB 6 dB 9 dB 6 dB 7 dB Test port unselected A, T4, T2, R1+, R1-, R2+, R2- 18 dB R3+, R3-, R4+, R4-, R4- T1, T2, T3 Interconnect port, typical P1, P2, P3, P4 Insertion loss Test port A, T4, R1+, R1-, R2+, R2-, 6 dB R3+, R3-, R4+, R4- T1, T2, T3 6 dB Stability per switch, typical 0.005 dB/ C Isolation Over arbitrarily test ports -100 dB 13 dB 12 dB 6 dB 9 dB 0.005 dB/ C -100 dB 7 dB 8 dB 9.5 dB 14.5 dB 0.015 dB/ C -80 dB 10.5 dB 12 dB 0.005 dB/ C 0.01 dB/ C -100 dB -100 dB Table 45. Front panel information Description RF connectors Interconnect ports Test ports (Option E5091A-009) Test ports (Option E5091A-016) General characteristics Type-N, female, 50 , nominal Number of ports 4 ports Type-N, female, 50 , nominal Number of ports 9 ports SMA, female, 50 , nominal Number of ports 25 ports (includes configurable switch port) 15 pin D-sub, female Control line Table 46. Rear panel information Description USB port www..com Line power 1 Frequency Voltage VA max General characteristics Type B-receptacle, provide connection to the E5071C 47 to 63 Hz 90 to 132 VAC, or 198 to 264 VAC (automatically switched) 150 VA max. 1. A third-wire ground is required. 52 Table 47. Test set dimensions and block diagram Description Dimensions Option E5091A-009 Option E5091A-016 Weight Option E5091A-009 Option E5091A-016 Block diagram Option E5091A-009/016 General characteristics See Figure 10, 12, and 13 See Figure 11, 12, and 15 6 kg 7 kg See Figure 15 Figure 10. Dimensions (front view, with Option E5091A-009, in millimeters, nominal) www..com Figure 11. Dimensions (front view, with Option E5091A-016, in millimeters, nominal) 53 Figure 12. Dimensions (rear view, in millimeters, nominal) Figure 13 Dimensions (side view, with Option E5091A-009, in millimeters, nominal) Figure 14. Dimensions www..com (side view, with Option E5091A-016, in millimeters, nominal) 54 Figure 15. Block diagram www..com 55 E5092A Configurable multiport test set The section provides test input/output performance without calibration by the E5071C. Table 48. Test set input/output performance Description Frequency range Damage level Specification 50 MHz to 20 GHz Typical 20 dBm, 35 VDC Table 49. Option E5092A-020 port performance Description Load match (selected port) SPDT switch1 50 MHz to 2 GHz 2 GHz to 4 GHz 4 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 18 GHz 18 GHz to 20 GHz SP4T switch2 50 MHz to 2 GHz 2 GHz to 3 GHz 3 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 18 GHz 18 GHz to 20 GHz Load match (unselected port) SPDT switch1 50 MHz to 3 GHz 3 GHz to 10 GHz 10 GHz to 16 GHz 16 GHz to 18 GHz 18 GHz to 20 GHz SP4T switch2 50 MHz to 3 GHz 3 GHz to 10 GHz 10 GHz to 16 GHz 16 GHz to 18 GHz 18 GHz to 20 GHz www..com 17 dB 11 dB 8 dB 6 dB 4 dB 17 dB 11 dB 8 dB 6 dB 4 dB 17 dB 11 dB 8 dB 7 dB 4 dB 4 dB 17 dB 11 dB 8 dB 7 dB 4 dB 4 dB Specification Typical 1. SPDT: Single-pole-double-throw switches. Applies to SW5, SW6, SW7, SW8, SW9 and SW10 in the E5092A. (See Figure 20.) 2. SP4T: Single-pole-four-throw switches. Applies to SW1, SW2, SW3 and SW4 in the E5092A. (See Figure 20.) 56 Table 49. Option E5092A-020 port performance (continued) Description Load match (common port) SPDT switch1 50 MHz to 2 GHz 2 GHz to 4 GHz 4 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 20 GHz SP4T switch2 50 MHz to 1.3 GHz 1.3 GHz to 4 GHz 4 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 20 GHz Insertion loss SPDT switch1 50 MHz to 100 MHz 100 MHz to 2 GHz 2 GHz to 3 GHz 3 GHz to 4 GHz 4 GHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 14 GHz 14 GHz to 18 GHz 18 GHz to 20 GHz SP4T switch2 50 to 100 MHz 100 MHz to 2 GHz 2 GHz to 3 GHz 3 GHz to 4 GHz 4 GHz to 6 GHz 6 GHz to 8 GHz 8 GHz to 10 GHz 10 GHz to 14 GHz 14 GHz to 18 GHz 18 GHz to 20 GHz Stability 50 MHz to 6 GHz 6 GHz to 20 GHz Isolation3 50 MHz to 500 MHz 500 MHz to 1 GHz www..com 1 GHz to 2 GHz 2 GHz to 6 GHz 6 GHz to 10 GHz 10 GHz to 18 GHz 18 GHz to 20 GHz 65 dB 80 dB 85 dB 90 dB 85 dB 75 dB 65 dB (Over arbitrarily test ports) 0.003 dB/C 0.01 dB/C (Stability per switch) 4 dB 3.5 dB 4.5 dB 5.5 dB 6 dB 7.5 dB 8.5 dB 9.5 dB 10.5 dB 12 dB 4 dB 3.5 dB 4.5 dB 5 dB 5.5 dB 7 dB 8 dB 8.5 dB 10 dB 11.5 dB 16 dB 11 dB 8 dB 7 dB 4 dB 16 dB 11 dB 8 dB 7 dB 4 dB Specification Typical 1. SPDT: Single-pole-double-throw switches. Applies to SW5, SW6, SW7, SW8, SW9 and SW10 in the E5092A. (See Figure 20.) 2. SP4T: Single-pole-four-throw switches. Applies to SW1, SW2, SW3 and SW4 in the E5092A. (See Figure 20.) 3. This specification is defined when all ports are terminated with a 50 ohm load. 57 Table 50. Control line Description Number of groups Specification 4 Group A: 8 bits Group B,C,D: 4 bits 0 V to +5 V (positive input) -5 V to 0 V (negative input) Group A, B: 50 mA in total of each group Group C, D: 500 uA in total of each group Typical Input voltage range1 Maximum current Impedance Group A, B: < 10 ohm Group C, D: < 200 ohm Table 51. DC source Description Number of sources Output voltage range Output voltage accuracy Voltage resolution Maximum current Output impedance 150 mA for each source < 5 ohm 3 % of setting (+1 V to +5 V) at 1 M ohm load impedance 10 mV (nominal)3 Specification 4 Typical 0 V to +5.2 V (nominal)2 Table 52. Operating storage environment Description Temperature Humidity Altitude Vibration General characteristics +5 C to +40 C 20 to 80% at wet bulb temperature < +29 C (non-condensing) 0 to 2,000m (0 to 6,561 feet) 0.21 G max., 5 to 500 Hz Table 53. Non-operating storage environment Description Temperature Humidity General characteristics -10 C to +60 C 20 to 90 % at wet bulb temperature < +40 C (non-condensing) 0 to 4,572 m (0 to 15,000 feet) 0.5 G max., 5 Hz to 500 Hz www..com Altitude Vibration 1. Input voltage will be clipped at about 5.2 V when over this range. 2. The output voltage can be set in this range. 3. The output voltage resolution becomes effective between 0 V to 5.2 V. 58 Table 54. Front panel information Description RF connectors Test ports Control line General characteristics SMA 38 ports 15-pin D-sub, female 25-pin D-sub, female Table 55. Rear panel information Description USB port Line power1 Frequency Voltage VA max General characteristics Type B-receptacle, provide connection to the E5071C 47 to 63 Hz 90 to 132 VAC, or 198 to 264 VAC (automatically switched) 300 VA max. Table 56. Test set dimensions and block diagram Description Dimensions E5092A Option 020 Weight E5092A Option 020 General characteristics See Figures 16, 17, 18 and 19 9 kg 426 192 129 18 Figure 16. Dimensions (front view, with Option E5092A-020, in millimeters, nominal) www..com 1. 1A third-wire ground is required. 59 133 40.6 40.6 40.6 36.8 17 27 27 27 27 27 27 27.8 13.5 27 69.8 Figure 17. Dimensions (pitch between switches, with Option E5092A-020, in millimeters, nominal) 129 37 18.57 23.38 65.34 83 Figure 18. Dimensions (rear view, with Option E5092A-020, in millimeters, nominal) 23 472 417 32 18 144 126 Figure 19. Dimensions (side view, with Option E5092A-020, in millimeters, nominal) www..com 60 13 133 146 51 22 133 23.38 132.72 SW 1 PORT 1 SW 2 PORT 2 SW 3 PORT 3 SW 4 PORT 4 1A 1B 1C 1D 5A 5B 6A 6B 2A 2B 2C 2D 7A 7B 3A 3B 3C 3D 8A 8B 9A 9B 4A 4B 4C 4D 10A 10B SW 5 SW 6 SW 7 SW 8 SW 9 S W 10 5C O M 6C O M 7C O M 8C O M 9C O M 10C O M Figure 20. Switch configuration (E5092A-020) Control Line 1 (Group A) DC Source (Group A) Max Current DC Source Output Output Impedance Output Voltage Negative Input (Low) Impedance Positive Input (High) Control Line 1 (Group A) Control Line 2 (Group A) Control Line 3 (Group A) Control Line 4 (Group A) : : : Control Line 8 (Group A) DC Source (Group B) DC Source Output Control Line 2 (Group B) Positive Input (High) Control Line 1 (Group B) Control Line 2 (Group B) Control Line 3 (Group B) Control Line 4 (Group B) Negative Input (Low) DC Source (Group C) DC Source Output Control Line 2 (Group C) Positive Input (High) Control Line 1 (Group C) Control Line 2 (Group C) Control Line 3 (Group C) Control Line 4 (Group C) Negative Input (Low) DC Source (Group D) DC Source Output Control Line 2 (Group D) Positive Input (High) Control Line 1 (Group D) Control Line 2 (Group D) Control Line 3 (Group D) Control Line 4 (Group D) Negative Input (Low) Figure 21. DC control line (E5092A-020) www..com 61 13 GND Line 4 Line 3 Line 2 25 12 24 11 GND Negative input www..com 23 GROUP B GROUP B Positive input 10 8 Line 8 Line 7 Line 6 Line 5 22 15 Line 1 GND DC source 9 7 21 14 Line 4 Negative input GND 8 6 GROUP A 20 13 Line 3 Positive input Negative input 7 5 19 D-SUB 25pin assignment D-SUB 15 pin assignment GROUP C Positive input 12 GROUP C GROUP A Line 2 Line 1 Line 4 Line 3 GROUP D DC source Reserved Reserved Reserved 6 4 18 5 17 DC source GND Line 4 11 3 Line 3 Figure 22. Control line pin assignment (E5092A-020) 10 4 2 16 3 15 Negative input GROUP D Line 2 9 1 Line1 Positive input 2 Line 2 Line 1 14 1 DC source 62 Corrected System Performance for 75 Measurements with 11852B 50 to 75 Minimum-Loss Pads (Supplemental Information) Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485 Table 55. Corrected system performance with type-N 75 device connectors, 85036E calibration kit Network analyzer: calibration kit: 50 to 75 adapters: calibration: E5071C 85036E (type-N 75 ) 11852B full 2-port IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 C 5 C with < 1 C deviation from calibration temperature, isolation calibration performed Description Directivity Source match Load match Reflection tracking Transmission tracking Typical (dB) 10 MHz to 3 GHz 37 33 39 0.015 0.019 Transmission uncertainty 10 MHz to 3 GHz (typical) Magnitude Transmission using 85036E and 11852B 10 100 Phase Transmission using 85036E and 11852B Mag (dB) 0.1 10 MHz to 3 GHz S11 = S22 = 0; Source power = -10 dBm Phase (deg) 1 10 1 10 MHz to 3 GHz S11 = S22 = 0; Source power = -10 dBm 0.01 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 0.1 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 Transmission coefficient (dB) Transmission coefficient (dB) Reflection uncertainty 10 MHz to 3 GHz (typical) Magnitude Reflection using 85036E and 11852B 0.1 10 MHz 0.08 www..com to 3 GHz Phase Reflection using 85036E and 11852B 10 8 10 MHz to 3 GHz S21 = S12 = 0; Source power = -10 dBm Mag (linear) S21 = S12 = 0; Source power = -10 dBm Phase (deg) 0.8 1 0.06 0.04 0.02 0 0 0.2 0.4 0.6 6 4 2 0 0 0.2 0.4 0.6 0.8 1 Reflection coefficient (linear) 63 Reflection coefficient (linear) www.agilent.com www.agilent.com/find/ena For more information on Agilent Technologies' products, applications or services, please contact your local Agilent office. The complete list is available at: Agilent Email Updates www.agilent.com/find/emailupdates Remove all doubt Our repair and calibration services will get your equipment back to you, performing like new, when promised. You will get full value out of your Agilent equipment throughout its lifetime. Your equipment will be serviced by Agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts. You will always have the utmost confidence in your measurements. For information regarding self maintenance of this product, please contact your Agilent office. Agilent offers a wide range of additional expert test and measurement services for your equipment, including initial start-up assistance, onsite education and training, as well as design, system integration, and project management. For more information on repair and calibration services, go to: www.agilent.com/find/removealldoubt Get the latest information on the products and applications you select. www.agilent.com/find/contactus Americas Canada Latin America United States Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Thailand Agilent Direct www.agilent.com/find/agilentdirect Quickly choose and use your test equipment solutions with confidence. (877) 894-4414 305 269 7500 (800) 829-4444 1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 1 800 226 008 www.lxistandard.org LXI is the LAN-based successor to GPIB, providing faster, more efficient connectivity. Agilent is a founding member of the LXI consortium. Europe & Middle East Austria 01 36027 71571 Belgium 32 (0) 2 404 93 40 Denmark 45 70 13 15 15 Finland 358 (0) 10 855 2100 France 0825 010 700* *0.125 /minute Germany 07031 464 6333 Ireland 1890 924 204 Israel 972-3-9288-504/544 Italy 39 02 92 60 8484 Netherlands 31 (0) 20 547 2111 Spain 34 (91) 631 3300 Sweden 0200-88 22 55 Switzerland 0800 80 53 53 United Kingdom 44 (0) 118 9276201 Other European Countries: www.agilent.com/find/contactus Revised: March 24, 2009 Product specifications and descriptions in this document subject to change without notice. www..com (c) Agilent Technologies, Inc. 2007-2009 Printed in USA, July 30, 2009 5989-5479EN |
Price & Availability of E5071C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |